Diode
You are here: Home>> Components>>Diode>>
  • Categories
  • Diode
  • Rectifier bridge
  • MOSFET
  • Other
  • 详解 TVS 管在手机 Circuit 中的详细 Application
    详解 TVS 管在手机 Circuit 中的详细 Application
  • 详解 TVS 管在手机 Circuit 中的详细 Application
  •   Published: 2018-12-05  Views: 2,333

     在实际的 Circuit 中, 如图所示, 在 DCinput 的时候, 有时由于供电环境的变化会带来一些瞬时脉冲. 而要消除瞬时脉冲对 Device 损害的最好办法, 就是将瞬时 Current 从敏感 Device 引到地, 一般具体做法是将 TVS 管在线路板上与被保护线路并联. 这样, 当瞬时 Voltage 超过 Circuit 正常工作 Voltage 后, TVS 管将发生雪崩击穿, 从而提供给瞬时 Current 一个超低阻抗的通路, 其结果是瞬时 Current 通过 TVS 管被短路到 GND, 从而避开被保护 Device, 并且在 Voltage 恢复正常值之前使被保护回路一直保持截止 Voltage. 而当瞬时脉冲结束以后, TVS 管再自动恢复至高阻状态, 整个回路又回到正常 Voltage 状态.

     





      典型的 Circuit 拓扑



      本文主要讲述通过在热插拔 Circuit 保护和 Automotive 电源线保护中典型 ApplicationCircuit 的实例, 详细探讨如何正确 ApplicationTVS 管 SMBJ5.0CA 和如何使其 Application 效果达到最佳. SMBJ5.0CA 具有 15KV 空气放电和 30KV 接触放电的 ESD 防护等级, 小于 1ps 的响应速率, 600w 的 10/1000us, duty 小于 0.01%的尖峰能量浪涌能量容量, 并且反向工作 Voltage 为 5V, 65A 下的钳位 Voltage 为 9V, 这些主要的电气特性使其非常适合在接口保护中.

     





      在智能仪表行业里一般采用 RS-485 通讯. 下图所示为 RS-485 通讯接口的典型 Application. 在保护 RS-485 接口不被静电或者浪涌损坏通常用 SMBJ5.0CA 来做接口保护如下图 3 所示, 当静电或者浪涌 Voltage 高于 5V 时, SMBJ5.0CA 会开始动作, 将 Voltage 钳位在很低的位置, 如果 Current 超过了峰值 CurrentIPP 话, 最终 Voltage 会被钳位在 9V 左右, 从而保护了后一级的 Device 不被损坏.




     

     


  • ·Previous:
    ·Next:
  • Related news
    Shenzhen Riyuechen Technology Co., Ltd.
    Address: 3/F, Building 27, Area A, Tantou Second Industrial City, Songgang, Bao'an District, Shenzhen
    Tel: +86 755 2955 6626
    Fax: 0755-2978 1585
    Mobile: +86 131 1300 0010
    Email:hu@szryc.com

    Shenzhen Riyuechen Technology Co., Ltd. All rights reserved. Copyright©2010-2027 www.szryc.com Tel: 13113000010 ICP License No. 2021111333 (Guangdong)